OSHA 1910.22 Housekeeping Rules for Plant Floors
OSHA's housekeeping rule for general industry, 29 CFR 1910.22, requires every workplace to keep its walking-working surfaces clean, orderly and sanitary, keep workroom floors as dry as is feasible, and remove hazards like spills, leaks, loose material, snow and ice. It also requires regular inspection of those surfaces and correction of hazards before anyone uses them. For a plant, that turns floor cleaning from a cosmetic job into a compliance item that inspectors can and do cite.
The text is short, but it applies to almost every square foot of a facility: production floors, aisles, mezzanines, loading docks, stairs, storerooms and service rooms. Below is how the rule reads, where plants usually get into trouble, and how to build a cleaning scope that holds up during an inspection.
What the standard actually says
OSHA rewrote Subpart D (Walking-Working Surfaces) in a final rule published in November 2016, and the updated 1910.22 took effect in January 2017. The general requirements sit in four parts.
Surface conditions, 1910.22(a). All places of employment, passageways, storerooms, service rooms and walking-working surfaces must be kept clean, orderly and sanitary. The floor of every workroom must be kept clean and, to the extent feasible, dry. Where a wet process is used, drainage has to be maintained and dry standing places, such as mats, platforms or false floors, provided where practicable. Surfaces must be free of hazards such as sharp or protruding objects, loose boards, corrosion, leaks, spills, snow and ice.
Loads, 1910.22(b). Each surface must be able to support the maximum intended load. This matters for cleaning when crews stage equipment or drums on mezzanines and grating.
Access and egress, 1910.22(c). Workers need a safe way on and off every walking-working surface. Pallets, hoses and cleaning carts left in the path count against you.
Inspection and repair, 1910.22(d). Surfaces must be inspected regularly and as needed, kept in safe condition, and any hazardous condition corrected, repaired or guarded before workers use the surface again. Repairs that affect structural integrity have to be done or certified by a qualified person.
Related rules inspectors read alongside it
Floors rarely get cited in isolation. Three other standards tend to show up in the same inspection.
- 1910.176, materials handling and storage. Aisles and passageways used by mechanical handling equipment must have sufficient clearance and be kept clear and in good repair. Storage areas must be kept free of accumulated material that creates tripping, fire, explosion or pest hazards.
- 1910.37(a)(3), exit routes. Exit routes must stay unobstructed by materials, equipment or locked doors. A floor scrubber parked in a corridor during a shift is a common finding.
- 1910.141(a)(3), sanitation. The sanitation standard repeats the clean and dry floor requirement and adds rules on waste receptacles and vermin control, which pulls break rooms, washrooms and waste areas into the same conversation.
If the plant produces fine dust, housekeeping also overlaps with the combustible dust National Emphasis Program. That topic has its own post on combustible dust housekeeping in winter.
How the rule gets applied on a real plant floor
Inspectors do not carry a cleanliness checklist with a pass mark. They look for conditions that create a hazard and then ask whether the employer knew, or should have known, about it. A few patterns account for most housekeeping problems.
Oil and coolant film. Machining and stamping areas build up a thin layer that looks dull rather than wet. It is slippery under boots and forklift tires, and it spreads with foot traffic. Mopping moves it around. Auto scrubbers with a degreaser matched to the oil, plus spot treatment at machine bases, actually remove it.
Wet process zones. Food plants, wash bays and plating lines are allowed to be wet, but the rule then expects working drains, sloped floors that drain toward them, and dry standing places. A clogged trench drain turns a compliant wet area into a citation.
Dock doors in winter. From November through March, snow and slush tracked in at receiving doors is one of the most common slip sources in northern plants. The standard names snow and ice directly. Matting, squeegee passes during heavy traffic and a scrub at shift change deal with it.
Debris in aisles. Shrink wrap, banding, broken pallets and swarf in travel lanes are both a trip hazard and a 1910.176 problem. These usually come from production, not from the cleaning crew, so the scope needs to say who picks up what and when.
Elevated surfaces. Mezzanines, catwalks and platforms are walking-working surfaces too. They collect dust and dropped parts, and they often get skipped because nobody owns them.
Building a cleaning scope that supports compliance
A good industrial cleaning scope maps the rule onto the actual floor plan. Plants that do this well tend to share the same structure.
- Zone the facility. Production, wet process, warehouse and dock, mezzanines, support areas (washrooms, break rooms, offices). Each zone gets its own method and frequency.
- Set frequencies by soil load, not by habit. A machining cell may need a scrub every shift, while a finished goods warehouse might be fine with a weekly pass and daily spot cleaning.
- Split operator and crew duties. Operators clean their stations and report spills right away. The crew handles floors, aisles, drains and the heavier detail work between shifts or on weekends.
- Write the spill response. Who responds, what absorbents and PPE are on hand, and how waste is bagged and labelled. A spill that sits for an hour is a hazard the employer knew about.
- Log inspections. 1910.22(d) wants regular inspection. A simple area checklist signed each shift or each week is the easiest way to show that it happened.
- Coordinate with lockout. Cleaning around or under machines falls under the control of hazardous energy rules. See the post on lockout/tagout rules for industrial cleaning.
The manufacturing plant cleaning service page lists what a production floor scope usually includes, from machine scrubbing with degreaser to industrial vacuuming of fines.
A note for Canadian plants
Canada has no single national rule like 1910.22. Each province sets its own. In Ontario, section 11 of the Industrial Establishments regulation (O. Reg. 851) requires floors and other surfaces used by workers to be kept free of obstructions, hazards and accumulations of refuse, snow or ice. Quebec, British Columbia, Alberta and the other provinces have comparable housekeeping and floor provisions in their own OHS regulations. Plants with sites on both sides of the border often adopt the stricter wording and run one program.
Frequently asked questions
Does OSHA 1910.22 require floors to be completely dry?
No. The rule says workroom floors must be kept dry to the extent feasible. Where a process is wet by nature, the employer must maintain drainage and provide dry standing places such as mats or platforms where practicable.
How often does OSHA require walking-working surfaces to be inspected?
The standard says regularly and as necessary, without a fixed interval. Most plants tie inspections to shifts in high-traffic production areas and to weekly rounds elsewhere, and they keep a written record so the inspections can be shown later.
Is the plant or the cleaning contractor responsible for a housekeeping citation?
On a multi-employer worksite OSHA can cite more than one party, including the employer that created, controlled or was expected to correct the hazard. In most cases the host plant carries the main responsibility for floor conditions, which is why the cleaning scope and spill response duties should be written down.
Do mezzanines and catwalks fall under the housekeeping rule?
Yes. Any horizontal or vertical surface a worker walks or works on is a walking-working surface under Subpart D, including mezzanines, platforms, catwalks, stairs and dock plates.
Get a scope that matches your floor plan
If your plant needs a cleaning program built around production zones, wet areas and winter dock traffic, send the details through the quote request form. Include floor types, shifts and the areas that cause the most trouble, and the scope can be written around how the plant actually runs.